Am einfachsten wäre es, wenn du
dir mal selbst die Anleitung durchliest und alle möglichen Optionen ansiehst.
-f umgeht die Prüfung von Hardware- und Firmware-IDs sowie von Prüfsumme
und Komptanilität/Plausibilität, presst die FW in den Falsch-ROM.
Das Rikiko, deine Karte zu "bricken", also zu einem Ziegelstein zu machen, wenn du
nicht weist, was du tust, nimmst du damit mit.
Wenigstens kommt bei der Version von 2015 eine Fehlermeldung beim flashen.
Ich schätze, da passt das Firmware-File nicht.
Wie hast du das verändert bzw. gespeichert?
Wo ist das Ursprungsfile her?
nvflash -?
gibt bei mir folgendes aus:
-- Primary Commands --
Update VBIOS firmware: nvflash [options] <filename>
Save VBIOS firmware to file: nvflash [options] --save <filename>
Display firmware bytes: nvflash [options] --display [bytes]
Check for supported EEPROM: nvflash [options] --check
Display VBIOS version: nvflash [options] --version [<filename>]
List adapters: nvflash [options] --list
Compare adapter firmware: nvflash [options] --compare <filename>
Verify adapter firmware: nvflash [options] --verify <filename>
Verify adapter IFR firmware: nvflash [options] --verify --ifronly <filename>
Display GPU ECID: nvflash [options] --ecid
Display License information: nvflash [options] --licinfo <filename>
Generate a License Request File: nvflash [options] --licreq <filename>,<reqType>
Provide a HULK license file: nvflash [options] --license <filename>
List out all the PCI devices: nvflash [options] --lspci
Access PCI Configure register: nvflash [options] --setpci
Display Build information: nvflash [options] --buildinfo
Display GMAC MCU version: nvflash [options] --querygmac
Update GMAC MCU firmware: nvflash [options] --proggmac <filename>.rom
Save GMAC MCU firmware to file: nvflash [options] --savegmac <filename>.rom
List GMAC MCUs: nvflash [options] --listgmac
Write protect EEPROM: nvflash [options] --protecton
Remove write protect: nvflash [options] --protectoff
Update Inforom firmware: nvflash [options] --flashinforom <filename>.ifr
Save Inforom firmware to file: nvflash [options] --save <filename>.ifr
Backup InfoROM to embedded IB: nvflash [options] --backupinforom
Restore InfoROM from embedded IB:nvflash [options] --recoverinforom
Read Inforom OBD info to file: nvflash [options] --rdobd <filename>
Read Inforom OEM info to file: nvflash [options] --rdoem <filename>
Update Inforom OEM info: nvflash [options] --wroem <filename>
Read uGPU license file to file: nvflash [options] --rdulf <filename>
Update uGPU license file to IR: nvflash [options] --wrulf <filename>
Display help screen for LIC OP: nvflash [options] --lichelp
Read HULK license file to file: nvflash [options] --rdhlk <filename>
Update HULK license file to IR: nvflash [options] --wrhlk <filename>
Flash a license file: nvflash [options] --licflash <filename>
Read UPR object to file: nvflash [options] --rdupr <filename>
Flash a UPR file: nvflash [options] --wrupr <compute|graphics>.upr
List the GPU mode: nvflash [options] --listgpumodes
Set the GPU mode to graphics: nvflash [options] --gpumode graphics
Set the GPU mode to compute: nvflash [options] --gpumode compute
Add a power policy entry: nvflash [options] --addpp TGP limitRated 250000
Delete a power policy: nvflash [options] --delpp TGP limitRated
List all current power policies: nvflash [options] --listpp
-- Commands and Options --
help ? [pp] Display help screen. pp for additional
help on power policies descriptions.
save b <filename> Read EEPROM and save to <filename>.
compare k <filename> Read EEPROM full content and compare with <filename>.
verify h <filename> Verify <filename> matches EEPROM if flashed.
version v <filename> Display firmware version information
(if no filename, acts on display adapter).
check c Check for supported EEPROM.
list a List all NVIDIA display adapters found in
the system.
protecton w Write protect EEPROM (only on some EEPROM's)
protectoff r Remove EEPROM write protect (only on some
EEPROM's).
license <license file> Provide a license file for updating VBIOS.
licinfo Display license file content. license file
is provided by --license option.
ecid Display GPU ECID.
licreq <file>,<reqType> Generate a License Request File by
specifying <reqType> to submit to Nvidia.
lspci List all the PCI devices in the system.
setpci <R.W>[=D[:M]] Read/Write PCI Config register.
Format is: <REG.WIDTH>[=DATA[:MASK]]
Read operation: <REG.WIDTH>
Write operation: <REG.WIDTH>=DATA[:MASK]
proggmac <filename> Flash GMAC MCU firmware (AI).
savegmac <filename> Read GMAC MCU firmware (AI) and
save to <filename>.
listgmac List all the GMAC MCU devices
querygmac [<filename>] Display GMAC MCU firmware (AI) version
(if no filename, acts on GMAC MCU device).
buildinfo Display build information for this tool.
display d [bytes] Display 256 the first bytes of the EEPROM
(default is 256 bytes).
createlic Create the License placeholder.
updateuefi u <filename> Update only the UEFI portion of the ROM
image from <filename>.
fullrecovery [foldername] Auto full recovery ROM from the backups.
gpumode graphics|compute Set the GPU mode to be either graphics or compute.
listgpumodes List the GPU mode of all NVIDIA adapters in the system.
addpp <policy> attr V Add a power policy. See '--help pp' for more details.
delpp <policy> attr Delete a power policy. See '--help pp' for more details.
listpp List all current power policies. See '--help pp' for more details.
flashinforom <filename> Flash InfoROM with data from <filename>.
backupinforom Backup InfoROM data to the embedded recovery
image.
recoverinforom R Restore InfoROM from embedded recovery image.
licflash <filename> Flash a license file.
lichelp Display help screen for license operations.
rdhlk <filename> Read HULK license file object to file.
wrhlk <filename> Install unlock license into EEPROM.
rdoem <filename> Read OEM object to <filename>.
wroem <filename> Write OEM object from <filename> to Inforom.
rdulf <filename> Read uGPU license file object to file.
wrulf <filename> Write uGPU license file object from file to Inforom.
rdupr <filename> Read uGPU Personality Request object to file.
wrupr <filename> Write uGPU Personality Request from file to Inforom.
rdobd <filename> [csv] Read OBD object to <filename> with optional csv format.
rmhlk Erase contents of the HULK object
skipmcuidchecks Allow to skip the IDs mismatch when flash MCU to an non-generic image.
offsysplxfilter Turn off system PLX bridge device filtering.
outfilepath <output path> Specify the location where the output file
should be saved. Works only with commands
'--gpumode' and '--listgpumodes'.
mergeinforom Merge InfoROM block if required.
reboot y Reboot the PC after other tasks completed.
filterdevid f <value>[,<mask>] Filter device list by device ID and optional
mask.
reversefilterid U <value> Remove item from the device ID list if
specified device ID is matched.
upgradeonly Only allow upgrading of firmware based on
version.
overridesub 6 Allow firmware and adapter PCI subsystem ID
mismatch.
index i <index> Force a specific device index.
pcisegbus B [<seg#>:]<bus#>: Select a specific device by using a specified
segment# and bus#. The following format
is allowed, <seg#>:<bus#>:<dev#>.<func#>.
All numbers are hexadecimal. The segment#
can be optional, and has a default value(0)
if no input value.The dev# and the func#
can be omitted for the --pcisegbus command.
auto A When possible, execute the specified command
without user intervention.
silence s Silence all audio beeps.
beep ! Beep to signal updating progress.
nolight l Do not light keyboard LEDs.
override o <level> Override safety check level:
default unknown EEPROM | NV adapter aborts application.
level=1 unknown EEPROM acceptable for read operations.
level=2 unknown NV adapter acceptable for read operations.
level=3 Combined effect of 1,2 (cannot write to unknown EEPROM or adapter).
log L <log file> Create a log file in truncat mode ( or add option --append in append mode )
nopowerchk p Skip power level check.
offswdriver S Turn off automatic switch driver state.
append Write log file in append mode.
guidcheck <GUID> Check if Build GUID match with VBIOS image
before proceeding.
fullbackup [foldername] Backup the existing ROM from display
adapter prior to flash.
Use a single dash ("-") to use the single letter version of a command.
Use a double dash ("--") to use the longer descriptive version of a command.
Use equals ("=") to specify parameters, with separating commas (",").
Reicht das als Hilfe?
Ne, Scherz. Asus hat der Karte zwar eine fette Platine, fette Spawas und 2x8 Pin Stromstecker spendiert, das Powerlimit aber auf maximal 286 Watt gesetzt. Die Karte fetzt schon bei original Spannung ins Limit.
